Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Cartridge type dry air filter
Cartridge type fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 18(dB) Maximum Allowable Back Pressure: 8.0 50 Hz / 10.0 60Hz
5 – CIRCUIT BREAKER TYPE
ABB 3 pole MCB. (4 pole is optional)
ALTERNATOR DATA
Make
Leroy Somer
Model
LSA42.3VS3
No. of bearings
1
Insulation class
H
Total Harmonic Content
at no load <3% – on load < 2%
Wires
12
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3 (wdg 6)
AYR Model
R220
Overspeed
2250 min¯¹
Voltage Regulation
± 0.5%
Short Circuit Capacity
–
PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6110
The DSE6110 is an Auto Start Control Module for single genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
RATINGS DEFINITION
Prime Power These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of commercially purchased power. 10% overload power is available for 1 hour in 12 hours continuous operation.
Standby Power These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a utility power. No overload is permitted on these ratings.
STANDARD REFERENCE CONDITIONS
Output ratings are presented at 25°C air inlet temperature, barometric pressure 100 kPa, relative humidity 30%. This generating set is designed to operate at high ambient temperatures (up to 55°C), humidity (up to 99%) and higher attitudes. De-ration may apply, please consult your dealer for specific site ratings.
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
STANDARD SPECIFICATIONS
6. FUEL SYSTEM On Generating Sets up to 700 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Two Cartridge type dry air filter
Cartridge type fuel filter
Three Full flow lube oil filter
All filters have replaceable elements
3 – TROPICAL COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 10(dB) Maximum Allowable Back Pressure: 8.0 (kPa)
5 – CIRCUIT BREAKER TYPE
ABB 3 pole ACB / MCCB (supplied disconnected and without cables)*
ALTERNATOR DATA
Make
Leroy Somer
Model
TAL 047D
No. of bearings
1
Insulation class
H
Total Harmonic Content
< 3.5% on load
Wires
6
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3 (n° 6)
AYR Model
R150
Overspeed
2250 min¯¹
Voltage Regulation
± 1%
Short Circuit Capacity
–
PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6110
The DSE6110 is an Auto Start Control Module for single genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
RATINGS DEFINITION
Prime Power These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of commercially purchased power. 10% overload power is available for 1 hour in 12 hours continuous operation.
Standby Power These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a utility power. No overload is permitted on these ratings.
STANDARD REFERENCE CONDITIONS
Output ratings are presented at 25°C air inlet temperature, barometric pressure 100 kPa, relative humidity 30%. This generating set is designed to operate at high ambient temperatures (up to 55°C), humidity (up to 99%) and higher attitudes. De-ration may apply, please consult your dealer for specific site ratings.
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
STANDARD SPECIFICATIONS
6. FUEL SYSTEM On Generating Sets up to 700 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Cartridge type dry air filter
Cartridge type fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 15(dB) Maximum Allowable Back Pressure: 10.0 @ 50 Hz / 15.0 @ 60Hz
5 – CIRCUIT BREAKER TYPE
ABB 3 pole MCB. (4 pole is optional)
ALTERNATOR DATA
Make
Leroy Somer
Model
LSA42.3M7
No. of bearings
1
Insulation class
H
Total Harmonic Content
at no load <3% – on load < 2%
Wires
12
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3 (wdg 6)
AYR Model
R220
Overspeed
2250 min¯¹
Voltage Regulation
± 0.5%
Short Circuit Capacity
–
PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6110
The DSE6110 is an Auto Start Control Module for single genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
RATINGS DEFINITION
Prime Power These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of commercially purchased power. 10% overload power is available for 1 hour in 12 hours continuous operation.
Standby Power These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a utility power. No overload is permitted on these ratings.
STANDARD REFERENCE CONDITIONS
Output ratings are presented at 25°C air inlet temperature, barometric pressure 100 kPa, relative humidity 30%. This generating set is designed to operate at high ambient temperatures (up to 55°C), humidity (up to 99%) and higher attitudes. De-ration may apply, please consult your dealer for specific site ratings.
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
STANDARD SPECIFICATIONS
6. FUEL SYSTEM On Generating Sets up to 700 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Cartridge type dry air filter
Two Cartridge type fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 15(dB) Maximum Allowable Back Pressure: 6.8 (kPa)
5 – CIRCUIT BREAKER TYPE
ABB 3 pole ACB / MCCB (supplied disconnected and without cables)*
ALTERNATOR DATA
Make
Leroy Somer
Model
TAL 047D
No. of bearings
1
Insulation class
H
Total Harmonic Content
< 3.5% on load
Wires
6
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3 (n° 6)
AYR Model
R150
Overspeed
2250 min¯¹
Voltage Regulation
± 1%
Short Circuit Capacity
–
PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6110
The DSE6110 is an Auto Start Control Module for single genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
RATINGS DEFINITION
Prime Power These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of commercially purchased power. 10% overload power is available for 1 hour in 12 hours continuous operation.
Standby Power These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a utility power. No overload is permitted on these ratings.
STANDARD REFERENCE CONDITIONS
Output ratings are presented at 25°C air inlet temperature, barometric pressure 100 kPa, relative humidity 30%. This generating set is designed to operate at high ambient temperatures (up to 55°C), humidity (up to 99%) and higher attitudes. De-ration may apply, please consult your dealer for specific site ratings.
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
STANDARD SPECIFICATIONS
6. FUEL SYSTEM On Generating Sets up to 700 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Air filter
Fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 13(dB) Maximum Allowable Back Pressure: 18.0 @ 50 Hz / 15.0 @ 50 Hz
5 – CIRCUIT BREAKER TYPE
ABB 3 pole MCCB. (4 pole is optional)
6. FUEL SYSTEM On Generating Sets up to 650 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
ALTERNATOR DATA
Make
Leroy Somer
Model
TAL 044D
No. of bearings
1
Insulation class
H
Total Harmonic Content
at no load < 2% – on load < 5%
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3
AVR Model
R120
Overspeed
2250 min¯¹
Voltage Regulation
± 1%
Short Circuit Capacity
–
AREP or PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6120
The DSE6120 is an Auto Mains (Utility) Failure Control Module suitable for a wide variety of single diesel or gas genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
RATINGS DEFINITION
Prime Power These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of commercially purchased power. 10% overload power is available for 1 hour in 12 hours continuous operation.
Standby Power These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a utility power. No overload is permitted on these ratings.
STANDARD REFERENCE CONDITIONS
Output ratings are presented at 25°C air inlet temperature, barometric pressure 100 kPa, relative humidity 30%. This generating set is designed to operate at high ambient temperatures (up to 55°C), humidity (up to 99%) and higher attitudes. De-ration may apply, please consult your dealer for specific site ratings.
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Cartridge type dry air filter
Cartridge type fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 13(dB) Maximum Allowable Back Pressure: 10.0 50 Hz / 15.0 60Hz
5 – CIRCUIT BREAKER TYPE
ABB 3 pole MCCB. (4 pole is optional)
6. FUEL SYSTEM On Generating Sets up to 700 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
ALTERNATOR DATA
Make
Leroy Somer
Model
TAL 044B
No. of bearings
1
Insulation class
H
Total Harmonic Content
< 2%
Wires
6
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3 (wdg 3)
AYR Model
R120
Overspeed
2250 min¯¹
Voltage Regulation
± 1%
Short Circuit Capacity
–
PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6110
The DSE6110 is an Auto Start Control Module for single genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
RATINGS DEFINITION
Prime Power These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of commercially purchased power. 10% overload power is available for 1 hour in 12 hours continuous operation.
Standby Power These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a utility power. No overload is permitted on these ratings.
STANDARD REFERENCE CONDITIONS
Output ratings are presented at 25°C air inlet temperature, barometric pressure 100 kPa, relative humidity 30%. This generating set is designed to operate at high ambient temperatures (up to 55°C), humidity (up to 99%) and higher attitudes. De-ration may apply, please consult your dealer for specific site ratings.
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Air filter
Fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 15(dB) Maximum Allowable Back Pressure: 8.0 @50 Hz / 10.0@ 60Hz
5 – CIRCUIT BREAKER TYPE
ABB 3 pole MCB. (4 pole is optional)
ALTERNATOR DATA
Make
Leroy Somer
Model
TAL 042C
No. of bearings
1
Insulation class
H
Total Harmonic Content
at no load <3% – on load < 2%
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3
AYR Model
R120
Overspeed
2250 RPM
Voltage Regulation
± 1%
Short Circuit Capacity
–
AREP or PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6120
The DSE6120 is an Auto Start Control Module for single genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
STANDARD SPECIFICATIONS
6. FUEL SYSTEM On Generating Sets up to 650 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Air filter
Fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 20(dB) Maximum Allowable Back Pressure: 10.2 (kPa)
5 – CIRCUIT BREAKER TYPE
ABB 3 pole MCB. (4 pole is optional)
ALTERNATOR DATA
Make
Leroy Somer
Model
TAL040F
No. of bearings
1
Insulation class
H
Total Harmonic Content
at no load <3.5% – on load < 5%
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3
AYR Model
R120
Overspeed
2250 RPM
Voltage Regulation
± 1%
Short Circuit Capacity
–
AREP or PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6120
The DSE6120 is an Auto Start Control Module for single genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software. Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
SOUND ATTENUATED AND WEATHER PROTECTIVE ENCLOSURE
Highly corrosion resistant construction: – Highly quality locks and hinges – Body made from galvanized steel components (2.0mm) treated with polyester powder coating.
Convenient access for maintenance: – Radiator fill access through cover in enclosure roof – Vertical hinged side door allowing 180° opening rotation
Transportability: – Tested and certified single point lifting facility. – Dragging points at base frame.
Security and safety:
Control panel, viewing window and a lockable access door
Emergency stop push button fixed externally for quick access
Cooling fan and battery charging alternator full fully guarded
Fuel fill and battery can only be reached via lockable across doors
Exhaust silencing system totally enclosed for operator safety
Sound pressure level:
80-85 dBA at 3 meters (standard)
IP rating IP45
Dimension and Weight (Closed Type)
Length cm
Width cm
Height cm
Weight Kg
Fuel Tank Litres
191
86
126.5
820
58
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
STANDARD SPECIFICATIONS
6. FUEL SYSTEM On Generating Sets up to 700 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
Perkins four stroke heavy duty high-performance industrial type Diesel engine.
2 – ENGINE FILTRATION SYSTEM
Air filter
Fuel filter
Full flow lube oil filter
All filters have replaceable elements
3 – COOLING RADIATOR
Radiator and cooling fan, complete with safety guards, designed to cool the engine at high ambient temperatures.
4 – EXHAUST SYSTEM
Heavy Duty Industrial Exhaust Silencer: Silencer noise reduction level: 22(dB) Maximum Allowable Back Pressure: 10.0 (kPa)
5 – CIRCUIT BREAKER TYPE
ABB 3 pole MCB. (4 pole is optional)
STANDARD SPECIFICATIONS
6. FUEL SYSTEM On Generating Sets up to 700 KVA, the baseframe design is incorporated with an integral fuel tank with a capacity of approx. 8 hours running at Full Load. The tank is supplied complete with full cap breather, fuel feed and return lines to the Engine and drain plug.
7. ALTERNATOR 7.1 INSULATION SYSTEM – The insulation system is Class H. – All windings are impregnated in either a triple dip thermosetting liquid, oil and acid resisting polyester varnish or vaccum pressure impregnated with a special polyester resin. – Heavy coat of antitracking varnish additional protection against moisture or condensation.
7.2 AUTOMATIC VOLTAGE REGULATOR (AVR) The fully sealed Automatic Voltage Regulator maintains the Voltage Regulation at 1% Nominal adjustment by means of a trim pot incorporated on the AVR.
7.3 MOTOR STARTING An overload capacity equivalent to 300% of the Full Load impedance at zero Power Factor can be sustained for 10 seconds, when PMG option is fitted.
8. MOUNTING ARRANGEMENT 8.1 BASE FRAME The complete Generating Set is mounted as a whole on a heavy duty fabricated steel Baseframe.
8.2 COUPLING The Engine and Alternator are directly coupled by means of an SAE flange. The Engine flywheel is flexibly coupled to the. Alternator rotor.
8.3 ANTI-VIBRATION MOUNTING PADS Anti-Vibration pads are affixed between the Engine/ Alternator feet and the Baseframe thus ensuring complete vibration isolation of the rotating assembly.
8.4 SAFETY GUARDS The Fan & Fan Drive along with the Battery Charging Alternator are Safety Guard protected for personnel protection.
9. FACTORY TESTS * The Generating set is load tested before dispatch * All protective devices control functions and site load conditions are simulated, The generator and its systems are checked before dispatch.
10. EQUIPMENT FINISHING All mild steel components are fully degreased and painted with powder coated paint to ensure maximum scuff resistance and durability.
11. DOCUMENTATIONS Operation & Maintenance manual, Circuit wiring diagrams, and Commissioning / Fault Finding Instruction leaflets are accompanied with the Generator.
12. QUALITY STANDARDS The equipment meets the following standards: BS4999, BS5000, BS5514, IEC 60034, VDEO530, NEMA MG 1 22 and ISO 8528
13. WARRANTY All of the Generating Sets are covered under a warranty policy for a period of 12 months. Warranty of the equipment is in line with manufacturer’s warranty terms & conditions.
In line with continuous product development, we reserve the right to change specifications without notice.
ALTERNATOR DATA
Make
Leroy Somer
Model
TAL040D
No. of bearings
1
Insulation class
H
Total Harmonic Content
at no load <3.5% – on load < 5%
Ingress Protection
IP23
Excitation System
SHUNT
Winding Pitch
2/3 (wdg 3)
AYR Model
R120
Overspeed
2250 min¯¹
Voltage Regulation
± 1%
Short Circuit Capacity
–
PMG Excitation System Available as Optional
CONTROL PANEL
Make
Deep Sea
Model
DSE6120
The DSE6120 is an Auto Mains (Utility) Failure Control Module suitable for a wide variety of single diesel or gas genset applications. It includes a backlit LCD display which clearly shows the status of the engine all the times. This module can either be programmed using the front panel or by using the DSE configuration suite PC software.
Metering and Alarm Indications: – Generator frequency – Underspeed, Overspeed – Generator volts (L-L, L-N) – Engine oil pressure – Engine coolant temperature – Fuel level (warning or shutdown) – optional – Hours run counter – Battery volts – Fail to start/stop – Emergency stop – Failed to reach loading voltage/frequency – Charge fail – Loss of magnetic pick-up signal – optional – Low DC voltage – CAN diagnostics and CAN fail/error
ALL INSPIRED DESIGN TO MEET YOUR NEEDS
SOUND ATTENUATED AND WEATHER PROTECTIVE ENCLOSURE
HIGHLY CORROSION RESISTANT CONSTRUCTION: High quality locks and hinges Body made from galvanized steel components (2.0mm) treated with polyester powder coating
CONVENIENT ACCESS FOR MAINTENANCE: Radiator fill access through cover in enclosure roof Vertical hinged side door allowing 180ᵒ opening rotation
TRANSPORTABILITY: Tested and certified single point lifting facility Dragging points at base frame
SECURITY AND SAFETY: Control panel viewing window in a lockable access door Emergency stop push button fixed externally for quick access Cooling fan and battery charging alternator fully guarded Fuel fill and battery can only be reached via lockable access doors Exhaust silencing system totally enclosed for operator safety
SOUND PRESSURE LEVEL:
80 – 85 dBA at 3 meters (standard)
IP Rating IP45 Customized enclosures with reduced Sound Pressure Levels available on demand
DIMENSIONS AND WEIGHT ( CLOSED TYPE )
Length cm
Width cm
Height* cm
Weight kg (wet)
Fuel Tank litres
191
86
126.5
749
58
AVAILABLE OPTIONS AND ACCESSORIES
We offer a range of optional features and accessories to tailor our generating sets to meet your power needs.
OPTIONS * A variety of generating set control and synchronizing panels * Additional protection alarms and shutdowns * Water fuel separator * Water jacket heater * Battery charger
ACCESSORIES * Genuine spare parts * Load banks * Auxiliary fuel tanks * Manual & automatic transfer switches
